Flexispot Standing Desk Evaluation …Flexispot 42 X 24…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of functions that I wasn’t necessarily a huge fan of:
The package that the desk can be found in was heavy, so bringing it inside was a group effort, however this is just an effect of how strong the Flexispot is.
The hassle-free cable tray was a bit confusing to set up. In the end, you ultimately slip it under screws, which wasn’t really clear from the instructions.
You will need to buy an anti-fatigue mat to stay comfy, but this is a good concept for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both thrilled (because this suggested it was going to be tough) and also a little hesitant (because all of us know just how much of an obstacle putting together furnishings can be).
Fortunately, with the help of a training YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t described well in the directions.
Once assembled, I like the sleek appearance of this desk. I’m positive any of the many varied finishes that it can be found in would look fantastic in any office, and the adjustable width makes it simple to fit it in even the tiniest of office.
The quiet operation and height memory settings make it easy, effective, and peaceful to change in between sitting and standing as lot of times as you desire throughout the day.
This desk is tough. It can hold up to 335 pounds even while in operation, so if you have a large desktop computer (or want to sleep on it for some reason) it has you covered. It will likewise uniformly disperse weight no matter how unbalanced the weight you place on it is, it will not wiggle or wobble.
in that video is quite kitted out as the desk we’re taking a look at today is pretty standard I tried to get as near that as I could on uplifts site with equivalent setups the flexi spot desk we’re taking a look at today will run you about four hundred and 10 dollars versus six hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift design is really 5 inches longer however you can do a lot with five inches boom yes now for transparency flexi spot did send this desk out for review but as you ought to understand by now does not affect my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping up until completion of April at the earliest the desktop is an inch thick however it’s this basic laminate as you can perhaps get doing not have even any cable television grommets for travel through the outside carton
for the desktop was not damaged in any way which is entirely unusual since I might shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted just very rough male if I had actually bought this I ‘d have been on the phone with customer service right away they did also managed to miss drilling the pilot holes where you can attach the control box to the desktop a great deal of needing to do that myself without mistakenly drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each part to support motorized function strangely absolutely where any type of cable television management materials whatsoever the frame on this unit is a single motor double stage design versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded also to both the dual phase double motor and a three-stage dual motor which pushes the cost of the desk up
an additional 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from simply under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than high enough even for me and I remain at 6 foot for this design does come basic with the control board that enables up-and-down movement plus three memory spots with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is extremely quiet as in barely audible this outside a rate would be the one advantage I would offer this unit over the uplift desk and I want to be careful here because this isn’t a hit piece this desk is 240 dollars cheaper than the comparable uplift design over 35% more affordable even if you update this flexi area test to the dual motor three-stage design it still comes in a hundred and seventy dollars more affordable than the uplift however cheaper doesn’t mean cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll definitely offer it that but the lateral stability of this desk the horizontal movement at this price point it’s undesirable it’s rub salt in the wound here they consist of a little security baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the sound and this baffle is definitely frustrating to leading things off I chose to include rolling casters to this desk this was a $30 upgrade and 2 of those four casters showed up damaged too my prepare for this desk at this moment is to lose the desk top and featured all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops up to 63 inches broad and 31 and a half inches deep so this will roll around the studio make it simpler to film products without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is an investment in quality workplace furnishings that will last you this at best feels like a cheaper imitation of that it just doesn’t feel quality and the difference in between this desk and my main desk is night and day do feel free to check out their website as well which likewise feels strangely similar to among their rivals there’s a wealth of accessories you can get for the flexi area desk approximately and consisting of a foot massager and even a fixed stationary bicycle and I might spend another 10 minutes of our valuable time covering various alternatives and devices I might however I think I’m better that they only sent out a standard desk due to the fact that as a fundamental desk I’m not a fan of the quality assurance at this rate point and I do not think slapping on a lot of extras is the move when the core item isn’t what it should be they do use a 30-day trial if you’re simply morbidly curious and they service warranty their desks for 3 years very desk is 5 years and uplift desk is seven years if you are Flexispot 42 X 24
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of video gaming and productivity however I would spend the additional money it’s gon na require to enter into a higher end maker like uplift desk or extremely desk and I have not personally utilized extremely desk products so I can’t speak on it but their track record is great big thanks to flexi spot for sending this out for review regrettably I can not suggest this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with viewing as how both the desktop and the casters got here damaged however from a client perspective you ‘d most likely be really thrilled to get this in