Flexispot Standing Desk Review …Flexispot Desk E22…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of functions that I wasn’t always a big fan of:
The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how durable the Flexispot is.
The convenient cable television tray was a little bit confusing to set up. In the end, you ultimately slip it under screws, which wasn’t really clear from the instructions.
You will need to buy an anti-fatigue mat to stay comfy, however this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both excited (considering that this meant it was going to be sturdy) and likewise a little hesitant (due to the fact that we all understand how much of a challenge putting together furnishings can be).
Thankfully, with the help of a training YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only problem I have with assembly was the cable television tray, which I discovered wasn’t described well in the directions.
As soon as assembled, I enjoy the streamlined look of this desk. I’m confident any of the many varied surfaces that it comes in would look excellent in any office, and the adjustable width makes it easy to fit it in even the tiniest of office.
The peaceful operation and height memory settings make it simple, efficient, and quiet to switch between sitting and standing as often times as you want throughout the day.
This desk is tough. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop computer (or wish to rest on it for some reason) it has you covered. It will also uniformly distribute weight no matter how out of balance the weight you put on it is, it will not wiggle or wobble.
because video is quite kitted out as the desk we’re looking at today is quite basic I attempted to get as near that as I might on uplifts website with comparable setups the flexi spot desk we’re taking a look at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift design is actually 5 inches longer however you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for review but as you need to know by now doesn’t affect my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping until the end of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can potentially get doing not have even any cable grommets for pass through the outside container
for the desktop was not damaged in any way which is absolutely unusual since I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted just super rough male if I had actually bought this I ‘d have been on the phone with customer service instantly they did also managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was in fact pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function unusually definitely where any sort of cable management products whatsoever the frame on this unit is a single motor double stage design versus the double motor three-stage style that comes standard with the uplift desk this can be updated too to both the dual stage dual motor and a three-stage dual motor which presses the cost of the desk up
an extra 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from simply under 28 inches to simply over forty seven point six inches so a max I ‘d it is more than high adequate even for me and I remain at 6 foot for this model does come standard with the control board that permits up-and-down motion plus 3 memory spots with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which needs to be changed as the width of the desk is adjusted the motor operation itself while it might be slow is very peaceful as in barely audible this outside a cost would be the one benefit I would give this unit over the uplift desk and I wish to beware here since this isn’t a hit piece this desk is 240 dollars less expensive than the equivalent uplift model over 35% cheaper even if you update this flexi area test to the double motor three-stage style it still is available in a hundred and seventy dollars more affordable than the uplift however less expensive doesn’t suggest cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely give it that however the lateral stability of this desk the horizontal motion at this price point it’s unacceptable it’s add insult to injury here they include a little security baffle this little steel piece that installs to the frame and covers a portion of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft strikes this baffle and the noise is absolutely infuriating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters showed up damaged also my prepare for this desk at this point is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it much easier to movie products without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is a financial investment in quality workplace furniture that will last you this at best feels like a less expensive replica of that it just doesn’t feel quality and the distinction in between this desk and my primary desk is night and day do do not hesitate to have a look at their site as well which also feels eerily similar to among their competitors there’s a wealth of devices you can get for the flexi area desk up to and consisting of a foot massager and even a fixed stationary bicycle and I might spend another 10 minutes of our precious time covering different options and accessories I could but I think I’m happier that they only sent out a standard desk because as a standard desk I’m not a fan of the quality assurance at this rate point and I don’t think slapping on a bunch of extras is the move when the core item isn’t what it should be they do use a 30-day trial if you’re simply morbidly curious and they guarantee their desks for 3 years very desk is five years and uplift desk is seven years if you are Flexispot Desk E22
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of video gaming and efficiency however I would spend the additional money it’s gon na take to enter a higher end manufacturer like uplift desk or very desk and I haven’t personally utilized extremely desk products so I can’t speak on it however their reputation is excellent huge thanks to flexi spot for sending this out for evaluation regrettably I can not advise this system and for the record I’m a hundred percent sure they would have gladly changed the parts that I had an issue with viewing as how both the desktop and the casters showed up damaged however from a consumer perspective you ‘d most likely be really excited to get this in