Get Flexispot Kana Pro Bamboo Standing Desk 2022

Flexispot Standing Desk Evaluation …Flexispot Kana Pro Bamboo Standing Desk…

Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a few functions that I wasn’t always a huge fan of:

The bundle that the desk was available in was heavy, so bringing it inside was a group effort, however this is just a consequence of how sturdy the Flexispot is.
The hassle-free cable tray was a bit confusing to set up. In the end, you ultimately slip it under screws, which wasn’t really clear from the instructions.
You will need to purchase an anti-fatigue mat to remain comfy, however this is a good concept for any standing desks, so I can’t fault Flexispot for that.

When it showed up and I saw how heavy it was, I was both excited (since this meant it was going to be sturdy) and also a little hesitant (due to the fact that we all understand just how much of a difficulty putting together furniture can be).

Luckily, with the help of an educational YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t discussed well in the directions.

As soon as assembled, I enjoy the sleek look of this desk. I’m positive any of the many varied finishes that it comes in would look great in any workplace, and the adjustable width makes it simple to fit it in even the smallest of office.

The peaceful operation and height memory settings make it easy, efficient, and peaceful to switch between sitting and standing as sometimes as you want throughout the day.

This desk is tough. It can hold up to 335 pounds even while in operation, so if you have a significant desktop computer (or wish to sleep on it for some reason) it has you covered. It will likewise evenly disperse weight no matter how out of balance the weight you place on it is, it will not wobble or wiggle.

 

because video is pretty kitted out as the desk we’re looking at today is pretty standard I tried to get as near to that as I could on uplifts site with equivalent configurations the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift design is in fact 5 inches longer however you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for review but as you need to know by now does not impact my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering up until completion of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can possibly get lacking even any cable grommets for pass through the outside carton

for the desktop was not damaged in any way which is absolutely unusual since I might shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just very rough guy if I had actually purchased this I ‘d have been on the phone with customer service right away they did likewise managed to miss drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without unintentionally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really quite uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function oddly absolutely where any sort of cable management materials whatsoever the frame on this unit is a single motor dual phase design versus the double motor three-stage design that comes requirement with the uplift desk this can be upgraded as well to both the double phase dual motor and a three-stage dual motor which pushes the cost of the desk up

an additional 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from simply under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall enough even for me and I remain at 6 foot for this design does come standard with the control panel that permits up-and-down movement plus 3 memory spots with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which needs to be changed as the width of the desk is adjusted the motor operation itself while it might be slow is really quiet as in barely audible this outside a rate would be the one advantage I would give this system over the uplift desk and I want to take care here due to the fact that this isn’t a hit piece this desk is 240 dollars more affordable than the equivalent uplift design over 35% less expensive even if you upgrade this flexi area test to the dual motor three-stage design it still is available in a hundred and seventy dollars less expensive than the uplift but less expensive does not indicate cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll absolutely offer it that but the lateral stability of this desk the horizontal movement at this price point it’s undesirable it’s rub salt in the wound here they include a little safety baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when

this desk sees any lateral motion at all the drive shaft strikes this baffle and the noise is absolutely infuriating to top things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those four casters showed up damaged too my plan for this desk at this point is to lose the desk top and included all together and replace it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it much easier to film products without needing to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality office furnishings that will last you this at finest seems like a more affordable replica of that it just does not feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to take a look at their website as well which likewise feels strangely comparable to one of their rivals there’s a wealth of accessories you can get for the flexi area desk as much as and consisting of a foot massager and even a fixed stationary bicycle and I could invest another 10 minutes of our precious time covering numerous options and accessories I might however I think I’m better that they just sent a standard desk since as a basic desk I’m not a fan of the quality assurance at this rate point and I do not believe slapping on a lot of extras is the move when the core item isn’t what it ought to be they do use a 30-day trial if you’re simply morbidly curious and they warranty their desks for 3 years extremely desk is five years and uplift desk is seven years if you are Flexispot Kana Pro Bamboo Standing Desk

in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in regards to gaming and performance but I would spend the extra money it’s gon na take to enter into a higher end manufacturer like uplift desk or extremely desk and I haven’t personally utilized very desk items so I can’t speak on it but their track record is excellent huge thanks to flexi area for sending this out for review sadly I can not recommend this system and for the record I’m a hundred percent sure they would have happily changed the parts that I had an issue with viewing as how both the desktop and the casters got here damaged however from a consumer viewpoint you ‘d most likely be truly thrilled to get this in