Get Flexispot Standing Desk E8 2022

Flexispot Standing Desk Review …Flexispot Standing Desk E8…

Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of functions that I wasn’t necessarily a substantial fan of:

The package that the desk was available in was heavy, so bringing it inside was a group effort, but this is simply a repercussion of how durable the Flexispot is.
The practical cable tray was a little bit confusing to set up. In the end, you eventually slip it under screws, which wasn’t really clear from the instructions.
You will need to purchase an anti-fatigue mat to remain comfy, but this is a great concept for any standing desks, so I can’t fault Flexispot for that.

When it showed up and I saw how heavy it was, I was both thrilled (since this indicated it was going to be sturdy) and likewise a little reluctant (due to the fact that we all know how much of a difficulty assembling furnishings can be).

Thankfully, with the help of an instructional YouTube link, it took me only around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only problem I have with assembly was the cable television tray, which I found wasn’t described well in the instructions.

As soon as put together, I enjoy the sleek appearance of this desk. I’m confident any of the many diverse surfaces that it comes in would look excellent in any workplace, and the adjustable width makes it easy to fit it in even the tiniest of home offices.

The quiet operation and height memory settings make it easy, efficient, and quiet to switch in between sitting and standing as many times as you want throughout the day.

Lastly, this desk is tough. It can hold up to 335 pounds even while in operation, so if you have a significant desktop (or want to rest on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how unbalanced the weight you place on it is, it will not wiggle or wobble.

 

because video is pretty kitted out as the desk we’re taking a look at today is quite standard I attempted to get as close to that as I could on uplifts site with equivalent setups the flexi area desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is actually 5 inches longer however you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for review but as you should know by now does not impact my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering until the end of April at the earliest the desktop is an inch thick however it’s this standard laminate as you can perhaps get doing not have even any cable television grommets for travel through the outdoors container

for the desktop was not damaged in any way which is entirely unusual since I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted just very rough guy if I had acquired this I ‘d have been on the phone with customer support instantly they did likewise managed to miss drilling the pilot holes where you can attach the control box to the desktop a lot of having to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function unusually absolutely where any type of cable television management products whatsoever the frame on this system is a single motor dual phase design versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded too to both the dual phase dual motor and a three-stage dual motor which presses the expense of the desk up

an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from simply under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall adequate even for me and I remain at 6 foot for this model does come basic with the control panel that enables up-and-down motion plus three memory spots with an LED readout to inform you the desk height the single motor design utilizes this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be slow is very quiet as in barely audible this outside a cost would be the one advantage I would provide this system over the uplift desk and I want to beware here since this isn’t a hit piece this desk is 240 dollars more affordable than the equivalent uplift model over 35% less expensive even if you update this flexi area test to the dual motor three-stage design it still can be found in a hundred and seventy dollars more affordable than the uplift but more affordable does not imply low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll absolutely offer it that but the lateral stability of this desk the horizontal movement at this cost point it’s inappropriate it’s rub salt in the wound here they include a little security baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when

this desk sees any lateral motion at all the drive shaft hits this baffle and the sound is absolutely frustrating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters showed up damaged also my plan for this desk at this point is to lose the desk top and came with entirely and replace it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it much easier to film items without needing to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furnishings that will last you this at best feels like a more affordable replica of that it just does not feel quality and the distinction in between this desk and my primary desk is night and day do do not hesitate to check out their website as well which likewise feels eerily similar to among their rivals there’s a wealth of accessories you can get for the flexi area desk approximately and including a foot massager and even a fixed exercise bike and I might spend another 10 minutes of our valuable time covering numerous choices and devices I could however I believe I’m happier that they just sent a basic desk due to the fact that as a basic desk I’m not a fan of the quality assurance at this cost point and I do not think slapping on a bunch of extras is the relocation when the core item isn’t what it need to be they do use a 30-day trial if you’re simply morbidly curious and they warranty their desks for three years really desk is 5 years and uplift desk is 7 years if you are Flexispot Standing Desk E8

in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in regards to video gaming and efficiency but I would invest the money it’s gon na take to enter into a higher end manufacturer like uplift desk or extremely desk and I have not personally used really desk items so I can’t speak on it however their track record is excellent huge thanks to flexi spot for sending this out for review sadly I can not suggest this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a problem with seeing as how both the desktop and the casters showed up damaged however from a client standpoint you ‘d most likely be truly delighted to get this in