Flexispot Standing Desk Review …Flexispot Standing Desk Installation Instructions…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a few features that I wasn’t necessarily a big fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a consequence of how strong the Flexispot is.
The hassle-free cable tray was a little bit complicated to set up. In the end, you ultimately slip it under screws, which wasn’t really clear from the directions.
You will require to purchase an anti-fatigue mat to stay comfortable, but this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both excited (considering that this suggested it was going to be durable) and also a little reluctant (due to the fact that we all know how much of a difficulty putting together furnishings can be).
Thankfully, with the help of a training YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t discussed well in the instructions.
As soon as put together, I enjoy the sleek look of this desk. I’m confident any of the many varied finishes that it is available in would look great in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of office.
The peaceful operation and height memory settings make it simple, efficient, and quiet to change between sitting and standing as often times as you desire throughout the day.
This desk is strong. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop computer (or want to sleep on it for some reason) it has you covered. It will likewise uniformly disperse weight no matter how out of balance the weight you place on it is, it won’t wiggle or wobble.
because video is quite kitted out as the desk we’re looking at today is pretty standard I tried to get as near that as I might on uplifts site with similar configurations the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift model is actually 5 inches longer however you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for evaluation however as you should know by now does not affect my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping until the end of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can potentially get lacking even any cable grommets for travel through the outside carton
for the desktop was not damaged in any way which is utterly strange since I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply super rough male if I had acquired this I ‘d have been on the phone with customer support right away they did also handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of needing to do that myself without unintentionally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was in fact pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each element to support motorized function strangely definitely where any sort of cable management materials whatsoever the frame on this unit is a single motor double phase style versus the double motor three-stage design that comes requirement with the uplift desk this can be upgraded also to both the double phase double motor and a three-stage double motor which pushes the expense of the desk up
an extra 70 dollars the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from simply under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than high adequate even for me and I stay at 6 foot for this design does come basic with the control board that enables up-and-down motion plus 3 memory spots with an LED readout to tell you the desk height the single motor design utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is really peaceful as in barely audible this outside a cost would be the one benefit I would provide this unit over the uplift desk and I want to take care here since this isn’t a hit piece this desk is 240 dollars less expensive than the similar uplift model over 35% less expensive even if you upgrade this flexi spot test to the double motor three-stage design it still can be found in a hundred and seventy dollars cheaper than the uplift but more affordable doesn’t indicate low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll absolutely offer it that however the lateral stability of this desk the horizontal movement at this rate point it’s unacceptable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft strikes this baffle and the noise is absolutely shocking to top things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters got here damaged as well my prepare for this desk at this point is to lose the desk top and included all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops up to 63 inches broad and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without needing to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furnishings that will last you this at best feels like a less expensive imitation of that it simply does not feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to take a look at their website also which also feels strangely similar to one of their rivals there’s a wealth of accessories you can get for the flexi spot desk as much as and consisting of a foot massager and even a fixed stationary bicycle and I could spend another 10 minutes of our valuable time covering different options and accessories I could however I think I’m better that they only sent a standard desk because as a fundamental desk I’m not a fan of the quality assurance at this cost point and I do not believe slapping on a lot of additionals is the relocation when the core product isn’t what it need to be they do offer a 30-day trial if you’re simply morbidly curious and they guarantee their desks for three years very desk is 5 years and uplift desk is seven years if you are Flexispot Standing Desk Installation Instructions
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in regards to gaming and performance but I would invest the extra money it’s gon na require to enter into a greater end maker like uplift desk or really desk and I haven’t personally used very desk items so I can’t speak on it however their track record is excellent big thanks to flexi spot for sending this out for evaluation unfortunately I can not suggest this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with seeing as how both the desktop and the casters got here damaged but from a consumer perspective you ‘d probably be truly delighted to get this in