Flexispot Standing Desk Review …Flexispot Vici Standing Desk…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of functions that I wasn’t necessarily a big fan of:
The plan that the desk came in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how tough the Flexispot is.
The practical cable tray was a little bit confusing to set up. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the directions.
You will require to purchase an anti-fatigue mat to stay comfortable, however this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both excited (considering that this meant it was going to be tough) and also a little reluctant (because we all understand just how much of a challenge putting together furniture can be).
The good news is, with the help of a training YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I discovered wasn’t described well in the directions.
Once assembled, I like the streamlined look of this desk. I’m confident any of the many varied surfaces that it comes in would look excellent in any workplace, and the adjustable width makes it easy to fit it in even the smallest of home offices.
The quiet operation and height memory settings make it easy, efficient, and quiet to change in between sitting and standing as many times as you want throughout the day.
This desk is strong. It can hold up to 335 lbs even while in operation, so if you have a significant home computer (or wish to take a nap on it for some reason) it has you covered. It will also uniformly disperse weight no matter how unbalanced the weight you place on it is, it won’t wiggle or wobble.
because video is quite kitted out as the desk we’re looking at today is quite basic I attempted to get as near to that as I could on uplifts site with comparable configurations the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is in fact five inches longer however you can do a lot with 5 inches boom yes now for transparency flexi spot did send this desk out for evaluation however as you must understand by now doesn’t affect my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping till the end of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can possibly get doing not have even any cable television grommets for go through the outdoors container
for the desktop was not damaged in any way which is absolutely unusual due to the fact that I might shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted simply incredibly rough male if I had bought this I ‘d have been on the phone with customer service right away they did likewise managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without mistakenly drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each component to support motorized function unusually definitely where any sort of cable television management products whatsoever the frame on this unit is a single motor double phase style versus the double motor three-stage design that comes requirement with the uplift desk this can be upgraded as well to both the dual phase double motor and a three-stage dual motor which pushes the cost of the desk up
an extra 70 bucks the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to simply over forty 7 point 6 inches so a max I ‘d it is more than tall sufficient even for me and I remain at 6 foot for this model does come basic with the control panel that enables up-and-down movement plus three memory spots with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which needs to be changed as the width of the desk is adjusted the motor operation itself while it might be sluggish is really quiet as in barely audible this outside a cost would be the one benefit I would provide this system over the uplift desk and I wish to take care here since this isn’t a hit piece this desk is 240 dollars less expensive than the comparable uplift model over 35% cheaper even if you update this flexi spot test to the double motor three-stage design it still can be found in a hundred and seventy dollars less expensive than the uplift however less expensive does not mean low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll definitely provide it that however the lateral stability of this desk the horizontal motion at this price point it’s inappropriate it’s add insult to injury here they include a little safety baffle this little steel piece that mounts to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft hits the noise and this baffle is definitely shocking to top things off I decided to add rolling casters to this desk this was a $30 upgrade and two of those four casters got here damaged too my prepare for this desk at this moment is to lose the desk top and included completely and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it much easier to movie products without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality office furniture that will last you this at best feels like a less expensive imitation of that it just doesn’t feel quality and the distinction in between this desk and my main desk is night and day do feel free to check out their website too which also feels eerily comparable to one of their competitors there’s a wealth of accessories you can get for the flexi area desk as much as and consisting of a foot massager and even a fixed stationary bicycle and I could invest another 10 minutes of our precious time covering different alternatives and accessories I might however I believe I’m better that they just sent a standard desk due to the fact that as a basic desk I’m not a fan of the quality assurance at this rate point and I don’t believe slapping on a bunch of extras is the move when the core item isn’t what it need to be they do provide a 30-day trial if you’re simply morbidly curious and they service warranty their desks for three years very desk is 5 years and uplift desk is 7 years if you are Flexispot Vici Standing Desk
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in regards to gaming and efficiency but I would spend the money it’s gon na require to get into a higher end manufacturer like uplift desk or very desk and I haven’t personally used really desk products so I can’t speak on it but their reputation is great huge thanks to flexi spot for sending this out for review unfortunately I can not advise this system and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with viewing as how both the desktop and the casters showed up damaged but from a customer standpoint you ‘d probably be truly delighted to get this in