Flexispot Standing Desk Review …Flexispot Won\’t Go Up…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of functions that I wasn’t necessarily a big fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, but this is simply a consequence of how durable the Flexispot is.
The practical cable tray was a bit confusing to install. In the end, you eventually slip it under screws, which wasn’t extremely clear from the directions.
You will need to purchase an anti-fatigue mat to stay comfortable, however this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both fired up (considering that this indicated it was going to be durable) and likewise a little reluctant (due to the fact that all of us understand just how much of a challenge putting together furnishings can be).
Luckily, with the help of an educational YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t explained well in the directions.
As soon as assembled, I love the sleek appearance of this desk. I’m positive any of the many diverse surfaces that it comes in would look fantastic in any workplace, and the adjustable width makes it simple to fit it in even the smallest of home offices.
The peaceful operation and height memory settings make it simple, efficient, and peaceful to change between sitting and standing as often times as you want throughout the day.
This desk is sturdy. It can hold up to 335 lbs even while in operation, so if you have a substantial desktop computer (or wish to rest on it for some reason) it has you covered. It will also uniformly distribute weight no matter how out of balance the weight you put on it is, it won’t wiggle or wobble.
because video is quite kitted out as the desk we’re taking a look at today is pretty basic I attempted to get as close to that as I could on uplifts site with equivalent setups the flexi area desk we’re taking a look at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is really five inches longer but you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for evaluation but as you need to know by now does not affect my review in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping till the end of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can potentially get doing not have even any cable grommets for go through the outside carton
for the desktop was not damaged in any way which is entirely bizarre since I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted just super rough man if I had actually purchased this I ‘d have been on the phone with customer service immediately they did likewise handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without mistakenly drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact quite simple the whole thing came together in about 45 minutes and despite the fact that there’s cable televisions running to it from each element to support motorized function unusually absolutely where any type of cable television management materials whatsoever the frame on this system is a single motor double phase design versus the dual motor three-stage style that comes requirement with the uplift desk this can be upgraded as well to both the double phase dual motor and a three-stage double motor which presses the expense of the desk up
an additional 70 bucks the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from simply under 28 inches to simply over forty seven point 6 inches so a max I ‘d it is more than high sufficient even for me and I stay at 6 foot for this design does come basic with the control board that enables up-and-down motion plus three memory areas with an LED readout to inform you the desk height the single motor style uses this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is really quiet as in barely audible this outside a rate would be the one advantage I would offer this unit over the uplift desk and I want to be careful here since this isn’t a hit piece this desk is 240 dollars more affordable than the similar uplift model over 35% cheaper even if you update this flexi spot test to the double motor three-stage design it still is available in a hundred and seventy dollars cheaper than the uplift however less expensive doesn’t imply low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll certainly provide it that but the lateral stability of this desk the horizontal movement at this cost point it’s undesirable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a portion of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the noise is definitely frustrating to top things off I decided to add rolling casters to this desk this was a $30 upgrade and two of those four casters got here damaged as well my plan for this desk at this point is to lose the desk top and included entirely and change it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is an investment in quality office furniture that will last you this at best feels like a more affordable replica of that it just doesn’t feel quality and the difference between this desk and my main desk is night and day do do not hesitate to check out their website as well which likewise feels strangely similar to one of their rivals there’s a wealth of accessories you can get for the flexi area desk up to and including a foot massager and even a fixed stationary bicycle and I could spend another 10 minutes of our precious time covering numerous options and accessories I might but I believe I’m happier that they only sent a standard desk since as a standard desk I’m not a fan of the quality assurance at this cost point and I do not think slapping on a bunch of bonus is the move when the core product isn’t what it must be they do use a 30-day trial if you’re just morbidly curious and they warranty their desks for 3 years extremely desk is 5 years and uplift desk is 7 years if you are Flexispot Won\’t Go Up
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and efficiency however I would spend the extra money it’s gon na take to enter a greater end manufacturer like uplift desk or very desk and I have not personally used really desk items so I can’t speak on it however their credibility is great huge thanks to flexi spot for sending this out for review regrettably I can not advise this unit and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a concern with viewing as how both the desktop and the casters arrived harmed however from a customer perspective you ‘d probably be truly delighted to get this in