Flexispot Standing Desk Review …Zenox Flexispot Dual-monitor Arm…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of features that I wasn’t necessarily a huge fan of:
The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a consequence of how tough the Flexispot is.
The convenient cable tray was a bit confusing to install. In the end, you ultimately slip it under screws, which wasn’t really clear from the directions.
You will require to buy an anti-fatigue mat to stay comfortable, but this is an excellent idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both thrilled (given that this indicated it was going to be strong) and also a little hesitant (due to the fact that all of us understand how much of an obstacle putting together furniture can be).
Thankfully, with the help of an educational YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable television tray, which I discovered wasn’t described well in the directions.
As soon as assembled, I enjoy the smooth appearance of this desk. I’m positive any of the many diverse surfaces that it is available in would look terrific in any office, and the adjustable width makes it simple to fit it in even the smallest of home offices.
The quiet operation and height memory settings make it easy, efficient, and quiet to change between sitting and standing as sometimes as you desire throughout the day.
Lastly, this desk is strong. It can hold up to 335 lbs even while in operation, so if you have a large desktop computer (or wish to sleep on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how unbalanced the weight you put on it is, it will not wobble or wiggle.
in that video is pretty kitted out as the desk we’re looking at today is pretty basic I tried to get as near to that as I could on uplifts website with comparable configurations the flexi area desk we’re taking a look at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift model is in fact 5 inches longer however you can do a lot with five inches boom yes now for openness flexi area did send this desk out for evaluation however as you should know by now does not affect my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering till the end of April at the earliest the desktop is an inch thick however it’s this basic laminate as you can perhaps get doing not have even any cable television grommets for pass through the outside carton
for the desktop was not damaged in any way which is utterly unusual since I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted just incredibly rough male if I had actually acquired this I ‘d have been on the phone with customer service immediately they did also handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually quite straightforward the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each element to support motorized function unusually definitely where any kind of cable television management products whatsoever the frame on this unit is a single motor dual stage design versus the double motor three-stage style that comes standard with the uplift desk this can be upgraded also to both the dual phase dual motor and a three-stage dual motor which pushes the expense of the desk up
an additional 70 dollars the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than high enough even for me and I stay at 6 foot for this model does come standard with the control board that enables up-and-down motion plus 3 memory areas with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is extremely peaceful as in barely audible this outside a rate would be the one advantage I would provide this system over the uplift desk and I want to take care here because this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift design over 35% less expensive even if you update this flexi area test to the dual motor three-stage style it still can be found in a hundred and seventy dollars less expensive than the uplift but more affordable does not imply cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll certainly provide it that but the lateral stability of this desk the horizontal movement at this rate point it’s undesirable it’s add fuel to the fire here they include a little safety baffle this little steel piece that installs to the frame and covers a part of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is definitely shocking to top things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those 4 casters showed up damaged too my plan for this desk at this point is to lose the desk top and featured all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops as much as 63 inches large and 31 and a half inches deep so this will roll around the studio make it simpler to film products without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality office furnishings that will last you this at finest seems like a cheaper imitation of that it simply does not feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to have a look at their website too which also feels eerily similar to one of their rivals there’s a wealth of accessories you can get for the flexi area desk approximately and including a foot massager and even a stationary exercise bike and I might spend another 10 minutes of our precious time covering different alternatives and accessories I could but I think I’m happier that they just sent a standard desk due to the fact that as a basic desk I’m not a fan of the quality assurance at this cost point and I don’t think slapping on a lot of additionals is the relocation when the core product isn’t what it need to be they do provide a 30-day trial if you’re simply morbidly curious and they warranty their desks for three years extremely desk is 5 years and uplift desk is 7 years if you are Zenox Flexispot Dual-monitor Arm
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to gaming and performance however I would invest the additional money it’s gon na require to get into a greater end producer like uplift desk or very desk and I have not personally utilized extremely desk products so I can’t speak on it but their reputation is excellent big thanks to flexi spot for sending this out for review unfortunately I can not suggest this unit and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with seeing as how both the desktop and the casters arrived damaged however from a client viewpoint you ‘d most likely be actually delighted to get this in